Light Overview
Overview of the RR and R2 Linear Lights
RR - What’s in the Box
| No. | Description | QTY | |
1 | R2 LED Linear Lightwith Ossium Rail(Q25R2 shown) | 1 | ||
2 | QS Slider | 1 | ||
3 | QS Dual ScrewBaby Pin | 1 | ||
4 | Q-Boot Silicon Bumpers | 2 | ||
N/A | 8ft AC Power Cable | 1 | ||
N/A | 8ft DC Power Cable:P-TAP to 2.1mm Barrel | 1 | ||
N/A | Quick Start Guide | 1 | ||
N/A | Short Cut Guide | 1 | ||
N/A | 3/16 Hex Wrench | 1 |
RR - Overview
*RR50 shown as reference | 1 | Power Side | |
2 | Lens Hatch | ||
3 | Slim Diffuser | ||
4 | Control Side | ||
5 | End Cap | ||
6 | (White Hexagons) | ||
7 | Mounting Holes | ||
8 | Ossium Rail | ||
9 | Heat Sink | ||
10 | End Cap |
RR Interface Layout
| 1 | “Link” Button | |
2 | Power On / Off | ||
3 | “Output” Button | ||
4 | LED Screen | ||
5 | “Data” Status Light | ||
6 | “Wireless” Status Light | ||
7 | “Right / +” Button | ||
8 | “Enter / Set” Button | ||
9 | USB-C Update Port | ||
10 | “Left / -” Button | ||
11 | LAN2 / DMX OUT | ||
12 | LAN1 / DMX IN | ||
13 | AC IN Port | ||
14 | DC IN Port: 2.1mm x 5.5mm |
Power Button: To turn the light on, press and hold for 1 second. To turn the light off, press and hold for 2 seconds. Double Tap the Power Button to Return to the Main Screen. When on the Main Screen, single tap the Power Button to get to the Sub Status Screen. To change the power on mode, to energize with to turn on when energized, without pressing the Power Button. See Section: Power On Mode.
Output Button: Toggle the button to enable/disable the lamp output in manual mode operation. Users can change the color, intensity or effect of the light without the changes affecting the environment before toggling the lamp back on. An Asterisk (*) appears in the top left corner of the screen whenever the Output Button is not allowing lamp output.
Link Button: On CRMX: For RX, press and hold to unlink light. For TX, Single tap to send pairing signal. Double Tap to bring up Wireless Menu
Left / Minus Button: Decrease a value or navigate Left.
Right / Plus Button: Increase a value or navigate Right.
Enter / Save Button: Enter selection, Save Value.
Upgrade Port: USB-C Port for performing software updates with a USB-C Thumb Drive.
R2 - What’s in the Box
| No. | Description | QTY | |
1 | R2 LED Linear Lightwith Ossium Rail(Q25R2 shown) | 1 | ||
2 | QS Slider | 1 | ||
3 | QS Dual ScrewBaby Pin | 1 | ||
4 | Q-Boot Silicon Bumpers | 2 | ||
N/A | 8ft AC Power Cable | 1 | ||
N/A | 8ft DC Power Cable:P-TAP to 2.1mm Barrel | 1 | ||
N/A | Quick Start Guide | 1 | ||
N/A | Short Cut Guide | 1 | ||
N/A | 3/16 Hex Wrench | 1 |
R2 - Overview
 | 1 | Power Side |
2 | Lens Hatch | |
3 | Slim Diffuser | |
4 | Control Side | |
5 | End Cap | |
6 | (White Hexagons) | |
7 | Mounting Holes | |
8 | Ossium Rail | |
9 | Heat Sink | |
10 | End Cap |
*Q25R2 shown as reference
R2 Interface Layout
| 1 | AC IN Port | |
2 | Power On / Off | ||
3 | “Data” Status Light | ||
4 | LED Screen | ||
5 | “Wireless” Status Light | ||
6 | “Right / +” Button | ||
7 | “Enter / Set” Button | ||
8 | “Output” Button | ||
9 | “Link” Button | ||
10 | “Left / -” Button | ||
11 | DMX OUT | ||
12 | DC IN Port: 2.1mm x 5.5mm | ||
13 | USB-C Update Port | ||
14 | LAN1 / DMX IN |
Power Button: To turn the light on, press and hold for 1 second. To turn the light off, press and hold for 2 seconds. Double Tap the Power Button to Return to the Main Screen. When on the Main Screen, single tap the Power Button to get to the Sub Status Screen. To change the power on mode, to energize with to turn on when energized, without pressing the Power Button.
Output Button: Toggle the button to enable/disable the lamp output in manual mode operation. Users can change the color, intensity or effect of the light without the changes affecting the environment before toggling the lamp back on. An Asterisk (*) appears in the top left corner of the screen whenever the Output Button is not allowing lamp output.
Link Button: On CRMX: For RX, press and hold to unlink light. For TX, Single tap to send pairing signal. Double Tap to bring up Wireless Menu
Left / Minus Button: Decrease a value or navigate Left.
Right / Plus Button: Increase a value or navigate Right.
Enter / Save Button: Enter selection, Save Value.
Upgrade Port: USB-C Port for performing software updates with a USB-C Thumb Drive.